| General specifications |
| Switching function | Normally closed (NC) |
| Output type | NAMUR |
| Rated operating distance | 15 mm |
| Installation | flush |
| Assured operating distance | 0 ... 12.15 mm |
| Reduction factor rAl | 0.4 |
| Reduction factor rCu | 0.3 |
| Reduction factor r304 | 0.85 |
| Output type | 2-wire |
| Nominal ratings |
| Nominal voltage | 8 V |
| Switching frequency | 0 ... 120 Hz |
| Current consumption | |
| Measuring plate not detected | min. 3 mA |
| Measuring plate detected | &le, 1 mA |
| Functional safety related parameters |
| MTTFd | 10750 a |
| Mission Time (TM) | 20 a |
| Diagnostic Coverage (DC) | 0 % |
| Compliance with standards and directives |
| Standard conformity | |
| NAMUR | EN 60947-5-6:2000
IEC 60947-5-6:1999 |
| Standards | EN 60947-5-2:2007
EN 60947-5-2/A1:2012
IEC 60947-5-2:2007
IEC 60947-5-2 AMD 1:2012 |
| Approvals and certificates |
| FM approval | |
| Control drawing | 116-0165 |
| UL approval | |
| Ordinary Location | E87056 |
| Hazardous Location | E501628 |
| Control drawing | 116-0451 |
| CSA approval | cCSAus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated &le,36 V |
| Ambient conditions |
| Ambient temperature | -25 ... 100 °C (-13 ... 212 °F) |
| Mechanical specifications |
| Connection type | screw terminals |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection!
tightening torque 1.2 Nm + 10 % |
| Core cross-section | up to 2.5 mm2 |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 |
| Housing material | PBT |
| Sensing face | PBT |
| Degree of protection | IP68 |
| Note | Tightening torque: 1.8 Nm (housing) |
| Equipment protection level Ga |
| CE marking | [*PD-Z02585A*] |
| ATEX marking | II 1G Ex ia IIC T6&hellip,T1 Ga
The Ex-related marking can also be printed on the enclosed label. |
| Standards | EN 60079-0:2012+A11:2013 EN 60079-11:2012
Ignition protection Intrinsic safety
Use is restricted to the following stated conditions |
| Appropriate type | NJ 15+U.+N... |
| Effective internal capacitance | max. 140 nF , a cable length of 10 m is considered. |
| Effective internal inductance | max. 130 µ,H , a cable length of 10 m is considered. |
| Ambient temperature | Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. Note: Use the temperature table for category 1 !!! The 20 % reduction in accordance with EN 1127-1 has already been applied to the temperature table for category 1. |
| Equipment protection level Gb |
| CE marking | [*PD-Z02585A*] |
| ATEX marking | II 1G Ex ia IIC T6&hellip,T1 Ga
The Ex-related marking can also be printed on the enclosed label. |
| Standards | EN 60079-0:2012+A11:2013, EN 60079-11:2012
Ignition protection Intrinsic safety
Use is restricted to the following stated conditions |
| Appropriate type | NJ 15+U.+N... |
| Effective internal capacitance | max. 140 nF , a cable length of 10 m is considered. |
| Effective internal inductance | max. 130 µ,H , a cable length of 10 m is considered. |
| Maximum permissible ambient temperature | Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. |
| Equipment protection level Da |
| CE marking | [*PD-Z02585A*] |
| ATEX marking | II 1D Ex ia IIIC T135°C Da
The Ex-related marking can also be printed on the enclosed label. |
| Standards | EN 60079-0:2012+A11:2013 EN 60079-11:2012
Ignition protection Intrinsic safety Use is restricted to the following stated conditions |
| Appropriate type | NJ15+U..-N.. |
| Effective internal capacitance | max. 140 nF , a cable length of 10 m is considered. |
| Effective internal inductance | max. 130 µ,H , a cable length of 10 m is considered. |
| General information |
| Use in the hazardous area | see instruction manuals |
| Category | 1G, 2G, 1D |
