| Application |
|---|
| Media | liquid refrigerants, oils, oily media, Water, water-like media |
| Dielectric constant of medium | 2 |
| Do not use for | strong conductive media, sticky media, granulates, bulk solids, acids, alkalis, food industry and electroplating |
| Max. level change rate [mm/s] | 200 |
| Reservoir pressure [bar] | 0.5, (when installed without mounting accessories: E43001 - E43007, E43019) |
| Coolants |
|---|
| Measured medium temperature [°C] | 0…35, (with climate tube E43101: 35…60 °C) |
| Oil |
|---|
| Measured medium temperature [°C] | 0…70 |
| Short-term medium temperature [°C] | 0…90, (< 1 h) |
| Water |
|---|
| Measured medium temperature [°C] | 0…35, (with climate tube E43101: 35…60 °C) |
| Electronic data |
|---|
| Operating voltage [V] | 18…30 DC |
| Current consumption [mA] | < 50 | < /tr>
| Protection class | III |
| Reverse polarity protection | yes |
| Power-on delay time [s] | < 3 |
| Inputs/outputs |
|---|
| Col Number of inputs and outputs | Number of digital outputs: 1, Number of analog outputs: 1 |
| Outputs |
|---|
| Total number of outputs | 2 |
| Output signal | switching signal, analogue signal, IO-Link |
| Electrical version | PNP/NPN |
| Number of digital outputs | 1 | < /tr>
| Output function | normally open / normally closed, (parameterizable) |
| Max. voltage drop DC switching output [V] | 2.5 |
| DC switching output load current [mA] | 200 |
| Number of analog outputs | 1 |
| Analog current output [mA] | 4…20, reversible |
| Maximum load [?] | 500 |
| Analog voltage output [V] | 0…10, reversible |
| Min. load resistance [?] | 2000 |
| Short circuit protection | yes |
| Type of short-circuit protection | Temperature, synchronized |
| Overcurrent protection | yes | < /tr>
| Measuring/setting range |
|---|
| Factory setting | liquid refrigerants, Water, water-like fluids | < /tr>
| Probe length L [mm] | 472 |
| Active range A [mm] | 390 |
| Inactive area I1 / I2 [mm] | 60 / 22 |
| Parameter setting within |
|---|
| Switching point SP [mm] | 35…390 |
| Reset point rP [mm] | 30…385 |
| Hysteresis [mm] | 5 |
| Reference point OP [mm] | 139 - 163 - 188 - 212 - 236 - 261 - 285 - 310 - 334 - 358 - 383 - 407 - OFF |
| Hysteresis, OP [mm] | 3 |
| Accuracy/Uncertainty |
|---|
| P measurement error [% of final value] | ± 5 |
| Repeatability | ± 2 |
| Resolution [mm] | 5 |
| Zero signal (voltage) [V] | 0 |
| Zero signal (current) [mA] | 4.0 |
| Full signal (voltage) [V ] | 10 |
| Total signal (current) [mA] | 20 |
| Software / Programming |
|---|
| Parameter selection | hysteresis / window, normally open / normally closed, switching logic, current output / voltage output, SP/rP position, OP setting, media selection, offset setting, turn on/off delay |
| Interfaces |
|---|
| Communication interface | IO-Link |
| Transmission method | COM2 (38.4 kBaud) |
| IO-Link test | 1.1 |
| SDCI standard | IEC 61131-9 |
| IO-Link device ID | 0x00028A |
Profiles | Smart Sensor: Process Data Variable, Device Identification, Device Diagnosis | | SIO Mode | yes |
| Desired port type | A |
| Analog operating data | 2 |
| Binary operating data | 1 |
| Minimum operating cycle time [ms] | 3.2 |
| Operating conditions |
|---|
| Ambient temperature [°C] | 0…60 |
| Storage temperature [°C] | -25…80 |
| Degree of protection | IP 67 | | |
| Tests / Approvals |
|---|
| EMC | | DIN EN 61000-6-4 | | | DIN EN 61000-6-2 | | < /tbody>
|
| Impact resistance | | DIN EN 60068-2-29 | 15 g (11 ms) |
|
| Vibration resistance | < table> |
| DIN EN 60068-2-6 | 5 g (10…2000 Hz) |
