| General specifications |
| Sensing range | 60 ... 800 mm |
| Adjustment range | 70 ... 800 mm |
| Dead band | 0 ... 60 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 255 kHz |
| Response delay | minimum : 13 ms
factory setting: 49 ms |
| Sensor cycle time | &ge, 13 ms (factory setting) ,
programmable to 60 s |
| Memory |
| Non-volatile memory | EEPROM |
| Write cycles | 300000 |
| Indicators/operating means |
| LED green | solid: Power on
flashing: Standby mode or IO-Link communication |
| LED yellow | solid: object in evaluation range
flashing: switch point programming, object detected |
| LED red | solid: error
flashing: switch point programming, object not detected |
| Electrical specifications |
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS |
| No-load supply current | &le, 40 mA |
| Power consumption | &le, 400 mW |
| Time delay before availability | &le, 300 ms |
| Interface |
| Interface type | IO-Link (via C/Q = Pin 4) |
| Device profile | Smart Sensor |
| Transfer rate | COM 2 (38.4 kBaud) |
| IO-Link Revision | 1.1 |
| Min. cycle time | 2.3 ms |
| Process data width | 16 bit |
| SIO mode support | yes |
| Device ID | 0x300302 (3146498) |
| Compatible master port type | A |
| Input/Output |
| Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 ... 1 V |
| 1 Level | 2.5 V ... UB |
| Input impedance | > 22 k&Omega, |
| Output rated operating current | current source < 2.5 mA |
| Pulse length | &ge, 1 ms with external control, low active |
| Synchronization frequency | |
| Common mode operation | &le, 82 Hz |
| Multiplex operation | &le, 82 Hz / n , n = number of sensors , n &le, 10
|
| Output |
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected |
| Rated operating current | 100 mA , short-circuit/overload protected |
| Voltage drop | &le, 2.5 V |
| Repeat accuracy | &le, ± 0.1 % of full-scale value |
| Switching frequency | factory setting: 12 Hz programmable max. 27 Hz |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm |
| Temperature influence | &le, ± 0.75 % of the end value (with temperature compensation)
from 10 minutes after switching on the sensor , 0,17 %/K (without temperature compensation) |
| Compliance with standards and directives |
| Standard conformity | |
| Standards | EN 60947-5-2:2007+A1:2012
IEC 60947-5-2:2007 + A1:2012
IEC 61131-9:2013
|
| Approvals and certificates |
| UL approval | cULus Listed, Class 2 Power Source |
| CCC approval | CCC approval / marking not required for products rated &le,36 V |
| Ambient conditions |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F)
When fixing with one M18 nut, the temperature range begins with 0 °C (32 °F). |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
| Mechanical specifications |
| Connection type | Connector plug M8 x 1 , 4-pin |
| Degree of protection | IP67 |
| Material | |
| Housing | Polycarbonate |
| Transducer | epoxy resin/hollow glass sphere mixture, polyurethane foam |
| Installation position | any position |
| Mass | 13 g |
| Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm
with M18 nuts max. 1 Nm |
| Factory settings |
| Output | near switch point: 70 mm
far switch point: 800 mm
Output mode: Window mode
Output logic: normally open |
| Beam width | wide |
