| Application |
|---|
| Media | liquid refrigerants, oils, oily media, Water, water-like media |
| Dielectric constant of medium | > 2 |
| Do not use for | strong conductive media, sticky media, granulates, bulk solids, acids, alkalis, hygienic media and electroplating |
| Max. level change rate [mm/s] | 200 |
| Reservoir pressure [bar] | 0.5, (when installed without mounting accessories: E43001 - E43007, E43019) |
| Coolants |
|---|
| Measured medium temperature [°C] | 0…35, (with climate tube E43101: 35…60 °C) |
| Oil |
|---|
| Measured medium temperature [°C] | 0…70 |
| Short-term medium temperature [°C] | 0…90, (<1 h) |
| Water |
|---|
| Measured medium temperature [°C] | 0…35, (with climate tube E43101: 35…60 °C) |
| Electronic data |
|---|
| Operating voltage [V] | 18…30 DC |
| Current consumption [mA] | <50 |
| Protection class | III |
| Reverse polarity protection | yes |
| Power-on delay time [s] | <3 |
| Inputs/outputs |
|---|
| Col Number of inputs and outputs | Number of digital outputs: 2 |
| Outputs |
|---|
| Total number of outputs | 2 |
| Output signal | Switching signal, IO-Link |
| Electrical version | PNP/NPN |
| Number of digital outputs | 2 |
| Output function | normally open / normally closed, (parameterizable) |
| Max. voltage drop DC switching output [V] | 2.5 |
| DC switching output load current [mA] | 200 |
| Short-circuit protection | yes |
| Short-circuit protection type | Temperature, synchronized |
| Overcurrent protection | yes |
| Measurement/setting range |
|---|
| Factory setting | Liquid refrigerants, Water, water-like media |
| Probe length L [mm ] | 472 |
| Active range A [mm] | 390 |
| Inactive area I1 / I2 [mm] | 60 / 22 |
| Parameter setting within |
|---|
| Switching point SP [mm] | 35…390 |
| Reset point rP [mm] | 30…385 |
| In increments of [mm] | 5 |
| Original point OP [mm] | 139 - 163 - 188 - 212 - 236 - 261 - 285 - 310 - 334 - 358 - 383 - 407 - OFF |
| Hysteresis, OP [mm] | 3 |
| Accuracy/Uncertainty |
|---|
| Measuring error [% of final value] | ± 5 |
| Repeatability | ± 2 |
| Resolution [mm] | 5 |
| Software / Programming |
|---|
| Parameter selection | hysteresis/window, normally open/normally closed, switching logic, SP/rP position, OP setting, media selection, offset setting, turn on/off delay |
| Interfaces |
|---|
| Communication interface | IO-Link |
| Transmission method | COM2 (38.4 kBaud) |
| IO-Link test | 1.1 |
| SDCI standard | IEC 61131-9 |
| IO-Link Device ID | 0x00028D |
| Profiles | Smart Sensor: Process Data Variable, Device Identification , Device Diagnosis |
| SIO Mode | yes |
| Required port type | A |
| Analog operating data | 2 |
| Binary operating data | 2 |
| Min. cycle time [ms] | 3.2 |
| Operating conditions |
|---|
| Ambient temperature [°C] | 0…60 |
| Storage temperature [°C ] | -25…80 |
| Degree of protection | IP 67 |
| Tests / approvals |
|---|
| EMC | | DIN EN 61000-6-2 | | | DIN EN 61000-6-4 | |
|
| Shock resistance | | DIN EN 60068-2-27 | 15 g (11 ms) |
|
| Vibration resistance | | DIN EN 60068-2-6 d> | 5 g (10…2000 Hz) |
|
| MTTF [years] | 265 |
| Mechanical data |
|---|
| Weight [g] | 435 |
| Dimensions [mm] | O 16 |
| Material | stainless steel steel (1.4301/304), stainless steel steel (1.4404 / 316L), FKM, NBR, PBT (polybutylene terephthalate), PC, PA (polyamide), PP, TPV Environment | PP |
| Displays / Controls |
|---|
| Display | | Display | 2 x LED, green (cm, inch) | | Output status | 2 x LED, yellow | | Measured values | alphanumeric display, 4 digits | | parameterization | alphanumeric display, 4 digits |
|
| Notes |
|---|
| Recommendations | Please see the technical note in the Downloads tab |
| Pack quantity | 1 piece |
| Electrical connection |
|---|
| Connection | Connector: 1 x M12 |
