| General specifications |
| Signal type | Analog input |
| Functional safety related parameters |
| Safety Integrity Level (SIL) | SIL 2 |
| Supply |
| Connection | terminals 9+, 10- or power feed module/Power Rail |
| Rated voltage | 19 ... 30 V DC |
| Ripple | within the supply tolerance |
| Power dissipation/power consumption | &le, 0.98 W / 0.98 W |
| Interface |
| Programming interface | programming socket |
| Input |
| Connection side | field side |
| Connection | terminals 1, 2, 3, 4 |
| RTD | type Pt10, Pt50, Pt100, Pt500, Pt1000 (EN 60751: 1995)
type Pt10GOST, Pt50GOST, Pt100GOST, Pt500GOST, Pt1000GOST (6651-94)
type Cu10, Cu50, Cu100 (P50353-92)
type Ni100 (DIN 43760) |
| Measuring current | approx. 200 µ,A with RTD |
| Types of measuring | 2-, 3-, 4-wire connection |
| Lead resistance | max. 50 &Omega, per line |
| Measurement loop monitoring | sensor breakage, sensor short-circuit |
| Thermocouples | type B, E, J, K, N, R, S, T (IEC 584-1: 1995)
type L (DIN 43710: 1985)
type TXK, TXKH, TXA (P8.585-2001) |
| Cold junction compensation | external and internal |
| Measurement loop monitoring | sensor breakage |
| Potentiometer | 0 ... 20 k&Omega, (2-wire connection), 0.8 ... 20 k&Omega, (3-wire connection) |
| Voltage | selectable within the range -100 ... 100 mV |
| Input resistance | &ge, 1 M&Omega, (-100 ... 100 mV) |
| Output |
| Connection side | control side |
| Connection | terminal 5: source (-), terminal 6: source (+), terminal 7: sink(-), terminal 8: sink (+) |
| Output | Analog current output |
| Current range | 0 ... 20 mA or 4 ... 20 mA |
| Fault signal | downscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43) |
| Source | load 0 ... 550 &Omega,
open-circuit voltage &le, 18 V |
| Sink | Voltage across terminals 5 ... 30 V. If the current is supplied from a source > 16.5 V,
series resistance of &ge, (V - 16.5)/0.0215 &Omega, is needed, where V is the source voltage.
The maximum value of the resistance is (V - 5)/0.0215 &Omega,. |
| Transfer characteristics |
| Deviation | |
| After calibration | Pt100: ± (0.06 % of measurement value in K + 0.1 % of span + 0.1 K (4-wire connection))
thermocouple: ± (0.05 % of measurement value in °C + 0.1 % of span + 1.5 K (1.7 K for types R and S))
this includes ± 1.3 K error of the cold junction compensation
mV: ± (50 µ,V + 0.1 % of span)
potentiometer: ± (0.05 % of full scale + 0.1 % of span, (excludes errors due to lead resistance)) |
| Influence of ambient temperature | deviation of CJC included:
Pt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K &Delta,Tamb*)
thermocouple: ± (0.02 K + 0.005 % of measurement value in °C + 0.006 % of span)/K &Delta,Tamb*)
mV: ± (0.01 % of measurement value + 0.006 % of span)/K &Delta,Tamb*)
potentiometer: ± 0.006 % of span/K &Delta,Tamb*)
*) &Delta,Tamb = ambient temperature change referenced to 23 °C (296 K) |
| Influence of supply voltage | < 0.01 % of span |
| Influence of load | &le, 0.001 % of output value per 100 &Omega, |
| Reaction time | worst case value (sensor breakage and/or sensor short circuit detection enabled)
mV: 1 s, thermocouples with CJC: 1.1 s, thermocouples with fixed reference temperature: 1.1 s, 3- or 4-wire RTD: 920 ms, 2-wire RTD: 800 ms, Potentiometer: 2.05 s |
| Galvanic isolation |
| Output/supply, programming input | functional insulation, rated insulation voltage 50 V AC
There is no electrical isolation between the programming input and the supply.
The programming cable provides galvanic isolation so that ground loops are avoided. |
| Indicators/settings |
| Display elements | LEDs |
| Configuration | via PACTware |
| Labeling | space for labeling at the front |
| Directive conformity |
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Conformity |
| Electromagnetic compatibility | NE 21:2011 |
| Degree of protection | IEC 60529:2001 |
| Protection against electrical shock | UL 61010-1:2004 |
| Ambient conditions |
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) |
| Mechanical specifications |
| Degree of protection | IP20 |
| Connection | screw terminals |
| Mass | approx. 100 g |
| Dimensions | 12.5 x 114 x 124 mm (0.5 x 4.5 x 4.9 inch) , housing type A2 |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| Data for application in connection with hazardous areas |
| EU-Type Examination Certificate | BASEEFA 13 ATEX 0102 X |
| Marking | II (1)G [Ex ia Ga] IIC , II (1)D [Ex ia Da] IIIC , I (M1) [Ex ia Ma] I |
| Input | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I |
| Inputs | terminals 1, 2, 3, 4 |
| Voltage Uo | 9 V |
| Current Io | 13.1 mA |
| Power Po | 30 mW |
| Analog outputs, power supply, collective error | |
| Maximum safe voltage | 250 V (Attention! This is not the rated voltage.) |
| Interface | |
| Maximum safe voltage | 250 V (Attention! The rated voltage is lower.), RS 232 |
| Certificate | BASEEFA 13 ATEX 0103 X |
| Marking | II 3G Ex nA II T4 Gc [device in zone 2] |
| Galvanic isolation | |
| Input/Other circuits | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| International approvals |
| UL approval | |
| Control drawing | 116-0379 (cULus) |
| IECEx approval | IECEx BAS 13.0057X |
| Approved for | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I |
| General information |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
