| General specifications |
| Sensing range | 60 ... 2000 mm |
| Adjustment range | 80 ... 2000 mm |
| Dead band | 0 ... 60 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 175 kHz |
| Response delay | minimum : 60 ms
factory setting: 120 ms |
| Indicators/operating means |
| LED green | Operating display |
| LED yellow 1 | switching state switch output 1 |
| LED yellow 2 | switching state switch output 2 |
| LED red | error |
| Electrical specifications |
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS |
| No-load supply current | &le, 50 mA |
| Interface |
| Interface type | Serial interface (programming adapter required)
9600 BPS, no parity, 8 data bits, 1 stop bit |
| Input/Output |
| Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 ... 1 V |
| 1 Level | 4 V ... UB |
| Input impedance | > 12 k&Omega, |
| Output rated operating current | < 12 mA |
| Pulse length | 0.5 ... 300 ms (level 1) |
| Pulse interval | &ge, 33 ms (level 0) |
| Synchronization frequency | |
| Common mode operation | &le, 30 Hz |
| Multiplex operation | &le, 33 Hz / n , n = number of sensors , n &le, 10
(factory setting: n = 5 ) |
| Output |
| Output type | 2 switch outputs PNP, NO/NC, programmable |
| Rated operating current | 200 mA , short-circuit/overload protected |
| Voltage drop | &le, 2 V |
| Repeat accuracy | &le, 0.1 % of full-scale value |
| Switching frequency | &le, 5 Hz |
| Range hysteresis | programmable , preset to 1 mm |
| Temperature influence | < 1.5 % of full-scale value |
| Compliance with standards and directives |
| Standard conformity | |
| Standards | EN 60947-5-2:2007+A1:2012
IEC 60947-5-2:2007 + A1:2012 |
| Approvals and certificates |
| EAC conformity | TR CU 020/2011 |
| UL approval | cULus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated &le,36 V |
| Ambient conditions |
| Ambient temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
| Mechanical specifications |
| Connection type | cable , 5-pin |
| Degree of protection | IP67 |
| Material | |
| Housing | PA-GF35 |
| Cable | PUR |
| Transducer | epoxy resin/hollow glass sphere mixture, polyurethane foam |
| Cable | |
| Sheath diameter | 7.25 mm |
| Bending radius | > 37.3 mm , fixed
> 74.7 mm , moving |
| Core cross-section | 5 x 0.82 mm2 |
| Length | 2 m |
| Mass | 345 g |
| Factory settings |
| Output 1 | near switch point: 80 mm
far switch point: 2000 mm
Output mode: Window mode
output behavior: NO contact |
| Output 2 | near switch point: 150 mm
far switch point: 1000 mm
Output mode: Window mode
output behavior: NO contact |
| Beam width | wide |
| Evaluation procedure | averaging (MxN)
M = 5
N = 2 |
| General information |
| Supplementary information | Switch settings of the external programming adapter:
output load: pull-down
output logic: inv |
