Honeywell 1CPSA2B

Honeywell 2CSP Series — MICRO SWITCH CPS Family of Cable-Pull Safety Switches: The 2CPS Series is intended for use in very long cable runs of 152 m [500 ft] or shorter, such as long conveyor lines found in warehouses.The 2CPS Series Cable Pull Safety Switch is designed to provide emergency stop protection for exposed conveyor lines. The internal mechanism latches on both slackened cable (push) and pulled cable. This capability enhances productivity by eliminating nuisance stops due to variations in temperature, stretch of cable over time, and other application variables. A line in the midpoint of the cable tension window indicates proper cable tension, providing easy and intuitive set-up. The direct acting switch contacts are held closed when the actuating cable is under proper tension and the reset knob is set to RUN. When the actuating cable is pulled, slackened or broken, a cam positively opens the NC (Normally Closed) switch contacts. The snap action, trip operation causes the switch contacts to change state and mechanically latch almost simultaneously when the cable is pulled, slackened or broken. The NC switch contacts remain open until the 2CPS is reset by properly tensioning the cable and manually rotating the reset knob. When the direct acting switch contacts open, the auxiliary contacts also actuate (open contacts close and closed contacts open). The auxiliary contacts are electrically isolated from the direct acting switch contacts. These NO (Normally Open) contacts may be used for monitoring or signaling. The 2CPS complies with: Low Voltage Directive 73/23/EEC, as amended by directive 93/68/EEC; Machinery Directive 98/37/EEC only as the directives relate to the components being used in a safety function; IEC/EN60947-1; IEC/EN60947-5-1; IEC/EN60947-5-5; UL, CE, CSA, SIL 3 capable. Honeywell’s MICRO SWITCH CPS Series Cable-Pull Safety Switches provide a readily accessible emergency stop signal, a cost-effective means compared to using multiple emergency stop push-buttons. The CPS Series Cable Pull Safety Switch’s internal mechanism latches on both slackened cable (push) and pulled cable. The CPS Series Cable Pull Safety Switch’s internal mechanism latches on both slackened cable (push) and pulled cable. The 1CPS is intended for use in applications where the cable span is 76 m [250 ft] or shorter. It is an economical solution for shorter runs or zone protection typical to automated systems. The 2CPS Series is intended for use in very long cable runs of 152 m [500 ft] or shorter, such as long conveyor lines found in warehouses. CPS Features:

Direct opening action of NC (Normally Closed) contacts

2CPS: 2NO/2NC, 1NO/3NC, or 4NC contact configurations

1CPS: 1NO/1NC, 2NO/2NC, 1NO/3NC, or 4NC contact configurations

Typical cable span of 76 m [250 ft] in an environment with a temperature change of ±17 °C [±30 °F]. Longer spans are possible depending upon temperature change and installation

Choice of three actuator configurations (2CPS)

Removable contact block version available (2CPS)

J-hook turnbuckle included (2CPS)

E-stop option (1CPS)

Low profile reset and new indicator options (2CPS)

Large wiring cavity with straight-through wiring

Models avaliable without broken cable, slack-cable detection

24 Vdc or 120 Vac bright, multi-cluster high-intensity LED status indicator light available on 2CPS. Single LED on 1CPS. Low profile LED (2CPS) and emergency stop button (1CPS) options also offered

Gold-plated contacts are standard on 2CPS, available on 1CPS

Electrostatic, epoxy-coated, die-cast zinc housing

Optional hardware packets available Applications:

Long conveyor systems found in warehouses and distribution centers

Conveyor systems with a high amount of vibration

Conveyor systems that experience wide temperature swings

Long conveyor systems where easy-through wiring, or highly visible trip status, is required

Perimeter guarding in hose-down conditions

Packaging equipment

Assembly lines